Turbo Volume Pump (Gas)

Overview

Turbo Volume Pump (Gas) (StructureTurboVolumePump) in Stationeers: device, hash 1310794736, 600 W. With build steps, 12 IC10 logic values and connection…

The turbo volume pump works like the Volume Pump: every tick it takes a fixed volume of gas at its input and pushes it into the network at its output, even against higher pressure. Its setting, however, runs from 0 to 100 instead of up to 10, and it ships at 50. On the mouse wheel the value jumps in steps of ten, with the fine adjustment in steps of one.

Two things differ from the small pump:

The direction can be switched: Mode 0 means Right, 1 means Left. Placing it the wrong way round is no reason to take it down.
Power and data have separate ports. You need one power cable and one data cable.

How much it really moves depends on the network at the input. Per tick the pump can draw at most what is in there. A single gas pipe holds 10 litres. If it hangs on ten pipe pieces (100 L) at 100 kPa and 20 °C, that is n = 100 · 100 / (8.3144 · 293) ≈ 4.1 mol – no more arrives in that tick, however high the setting. An in-line tank in front of the input gives it the reserve it needs.

Base draw is 600 W, three times that of the small pump. In IC10 you switch it with On, set the amount with Setting and the direction with Mode. The kit comes from the Hydraulic Pipe Bender, and placing it takes one step. More on throughput and control in Pumps, valves and pressure regulators: which part for what and The volume pump in depth.

IC10 and logic

12 logic values, 12 readable and 4 writable.

Power R 1
Mode RW 3
Error R 4
Lock RW 10
Setting RW 12
Maximum R 23
Ratio R 24
On RW 28
RequiredPower R 33
PrefabHash R 84
ReferenceId R 217
NameHash R 268

Example: address by name

Reads Setting, shows the value on the IC housing and writes On. Name the device with the labeller first; devices with the same name are addressed together.

# Turbo Volume Pump (Gas) address by name
define DEVICE 1310794736  # StructureTurboVolumePump
define NAME HASH("Turbo Volume Pump (Gas)")  # name in game (labeller)
define TARGET 1  # On 1 = on
alias value r0

start:
yield
lbn value DEVICE NAME Setting 0  # 0 = average of all with this name
bnan value start  # no device with this name
s db Setting value  # show on the housing
sbn DEVICE NAME On TARGET  # set value
j start

Academy: devices by name Academy: batch modes IC10 academy IC10 editor

Connections

Schematic: inputs left, outputs right, waste on top, power and data at the bottom. Position and spacing do not match the model.

1Data
2Power
3Gas pipe · output
4Gas pipe · input

Slots and modes

Modes: 0 = Right, 1 = Left

Building and deconstruction

Grid: small grid (0.5 m) · mounting: free in the grid

1
Place
- Kit (Turbo Volume Pump - Gas)
Take back with Hand Drill

Total material

Kit (Turbo Volume Pump - Gas)

Deconstruction returns

Kit (Turbo Volume Pump - Gas)

Built with: Kit (Turbo Volume Pump - Gas)

Raw values from the game code (7)

Field names as in the game code, untranslated. Useful for mods and exact limits.

`VolumePump.wheelSettingIncrement`	10
`VolumePump.wheelAltSettingIncrement`	1
`DeviceAtmospherics.outputSetting`	50
`DeviceAtmospherics.pressurePerTick`	101.3
`DeviceAtmospherics.MinSetting`	0
`DeviceAtmospherics.MaxSetting`	100
`DeviceAtmospherics.ConnectionType`	Exhaustive